DIY Tub Installation.
DIY Tub Installation.
Blog Article
Everyone may have their personal thinking about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old tub is readily accessible, the task can relocate rapidly; if you have to open a wall surface to eliminate the old tub and also place the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require an assistant to leave the old tub as well as set in the brand-new one. Make certain you have actually qualified yourself for the work and also fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new bath tub in your restroom if you have actually currently purchased a brand-new tub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools and also product checklist need to make up the following:
Getting ready for the Installment
First of all, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Before carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bath tub up until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has been utilized at least when as this will settle it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers are in location between the faucet and also the sink. Secure the faucet in place with the maker provided backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall between the bathroom and also the tiling, bring about complications with moisture as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture rather very early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very focused on Installing A Bathtub and I'm hoping you enjoyed reading my blog post. For those who enjoyed reading our article plz remember to pass it around. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule Here Report this page